| Press Ctrl-D to add us to Your browser favorites ! | |
|
|
| Reconditioned Power Tools | |
|
|
|
| Delta 17-959L 17 Inch Laser Crosshair Drill Press - 16 Speed | 
 enlarge | Brand: Delta
Category: Home Improvement
List Price: $1,014.00
Buy New: $579.00
You Save: $435.00 (43%)
New (3) from $579.00
Sales Rank: 15881
Media: Tools & Hardware
Shipping Weight (lbs): 262
Dimensions (in): 57 x 26.2 x 11
MPN: 17-959L 90894
Model: 17-959L
UPC: 069554179594
EAN: 0069554179594
Shipping: Eligible for Super Saver Shipping
Availability: Usually ships in 24 hours
|
| Features:
|
| Accessories:
|
| Similar Items:
|
| Editorial Reviews:
Amazon.com Product Description
Precision is important to any drill press user and the DELTA 17-959L Crosshair Drill Press offers accuracy with its fully adjustable , powered laser pod that projects a bright red crosshair at the point of bit contact. The press is constructed with industry leading features, including an 18 by 14 inch tilting table with the ability to tilt 0-90 degrees to the left or right and 0-45 degrees forward. Additionally, it has positive stops at 0, 45, and 90 degrees to aid in time efficiency. The DELTA 17-959L also allows you to firmly and accurately secure your work piece, whether it be wood, plastic or metal, with a variety of attachments and accessories. Other innovative features include: the flexible incandescent task light, heavy-duty 3/4 horse power motor, 16 drilling speeds, and a full 4-7/8 inch quill stroke for deeper drilling applications.
|
| Customer Reviews: Read 4 more reviews...
 Poor tool at any price November 22, 2008
1 out of 1 found this review helpful
This drill press represents the worst in mainland Chinese manufacturing. Delta is squandering their good name with products like this. The casting are rough throughout. The pulleys are unbalanced, the drive belts are stiff. The idler pully shaft and the shafts used as part of the belt tensioning system ride in holes drilled in the head casting. No bushings are used and the play can be measured in fractions of inches. As you apply tension to the belts, the motor shifts upward causing the drive belt to skew upward. The poor build results in a lot of vibration especially at higher speeds. The laser adjustments are poorly designed and the beam width at working distances are too thick for precise hole designation. I haven't measured runout because I wouldn't bother using this drill on any precision work. The best I can say for this drill press is that it will drill a hole. I wouldn't expect it to last for long however.
 Not a bad drill for the money November 18, 2008
1 out of 1 found this review helpful
I've recently purchaced the drill with expectations of a 500$ item and that's what i recieved. I do use this product alot and it is a very nice drill for the home or garage only drawback i encountered was the table .
In my eyes it is build very cheaply but i'm used to being around 5000$ clausings . But for all the wood and metal i drilled so far i haven't stalled it lol. All this tool needs is a little tlc and some home made hardware. I think on all these types of tools they scimp on the hardware.Overall it really does the job.
 Fair Drill Press October 28, 2008
4 out of 4 found this review helpful
I purchased this drill press on a Wednesday morning from Amazon with Free Super Saver Shipping and by Friday evening at 6:00 p.m. it was in my shop ready to be set up. I had been looking for a floor mounted drill press for some time to replace my Craftman benchtop press. I was very interested in the Powermatic PM 2800 but the cost, poor or mediocre reviews, with it's limited ability to drill into steel/metal combined with what appeared to be a difficulty to mount standard drill press vices on its table drove me to look elsewhere. The Grizzly and Steel City 17" presses looked nice but they had standard metal working tables that did not tilt forward and the Jet had poor/o.k. reviews. The Delta 17" had decent power, a large wood and steel working table that tilted forward and a laser which made it a logical choice. It's price through Amazon along with free shipping made it a good and economical choice for my shop. I don't mind the time for belt changes versus the varible speed Powermatic, so I placed the order.
The unit was delivered with no problems. A drill press is a pretty basic set up and the manual covered everything in plenty of detail. However, the manual for the Grizzly and Steel City presses are superior and provide better set-up options (i.e. install press head on pole and then lift up, not anchor the press to the floor and lift the head on top of the pole). Also other manufactures provided an explanation for the drift key to change the drill chuck, which Delta left out completely. Grizzly did a nice job on providing basic instructions on how to properly and safely use the press, which would be nice for a novice, a fact which Delta left out completely. A nice thing Delta did provide was a chart with drill bits and speeds for you to post in your shop as a rapid check for the belt set-up.
As for the press, it is well constructed and went together very well. The external light came with a metal clip to anchor the electrical chord versus the plastic units shown in the manual. The instructions gave no indication of where to put the metal clip, but a close inspection of the press head identified a threaded hole near the motor where the clip mounted perfectly. The laser took a few minutes to set up but does work very well at various table locations. I was able to square the table to the chuck in both directions with no prbolems and the chuck had 0.005" of runout. The T-slots work excellent with clamps and make the unit very easy to use. The table is great for using C-clamps as there are no edge rigids on the underside.
The belts change very quickly and the press does what it is supposed to. The quill lock is easy to use and the depth gauge changes rapidly. The only reason I gave this press 4 stars was the vibration in the unit. Although it is not terrible, I expected a little better. After some use and tweaking of the pullies, it did get better results but I will be repalcing the stock belts to see if this settles it down a bit in the future.
 Great Machine June 28, 2008
1 out of 4 found this review helpful
My husband is extremely pleased with the drill press. All of the parts arrived safely and assembly was quite easy.
A good solid drill press May 5, 2008
7 out of 7 found this review helpful
A well built drill press solid enough for accurate work.
The assembly manual states that unless the stand if fastened to the floor, an auxiliary stand of 3/4 plywood is necessary. I made mine about 6 inches to either side, and a couple of feet more in the front for convenience in standing. I put thin strips around part of the edge to slip a dolly under it in case I want to move it. Oh, and if you want to use 230 volts, you need to change the switch.
The laser sight is quite convenient, but the mounting system is not yet well developed. It is tricky to align. All in all, though, a good tool for the price.
|
| Power Tools - Home Improvement Articles |
|
01/08/2009 01:13 AM
|
|
WOODSMITH: Sander stand
|
Sanding is certainly one of the least engaging tasks in woodworking. Using a random-orbit sander is a great way to shorten the job and make it more tolerable. And I came up with a simple way to make my sander even more efficient.
Continue reading: "WOODSMITH: Sander stand".
|
|
01/01/2009 01:20 AM
|
|
SHOPNOTES: Success with Threaded Inserts
|
Threaded inserts are must-haves in my shop. I keep them on hand for building jigs and fixtures I need to adjust easily. The challenge with an insert is installing it without any problems. But I've picked up a few tips to get great results.
Continue reading: "SHOPNOTES: Success with Threaded Inserts".
|
|
12/25/2008 01:11 AM
|
|
WOODSMITH: Turnbutton drawer catch
|
Sometimes those annoying, everyday problems can have very simple solutions. Here's one I think you'll find useful.
Continue reading: "WOODSMITH: Turnbutton drawer catch".
|
|
12/18/2008 01:19 AM
|
|
SHOPNOTES: Cutting Plastic
|
From time to time, I need to use plastic in shop projects or jigs. But cutting it can be messy. I've learned a few tips that will give you smooth cuts, every time.
Continue reading: "SHOPNOTES: Cutting Plastic".
|
|
12/11/2008 01:10 AM
|
|
WOODSMITH: Cord and hose boom
|
Keeping the floor free of hazards can make you shop a lot more "user-friendly." Take a look at one solution I came up with.
Continue reading: "WOODSMITH: Cord and hose boom".
|
|
|
|
|
|
In association with amazon.com. (c) 2006-207 Reconditioned-Power-Tools.com
Refurbished and Reconditioned Power Tools
Financial Blog | Microcap Stocks | Free Stock Tips | |
